Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

01/05/2014

 Toyota (Pts.)

0

2014 Toyota Camry G Key remote starter crank but not start

Hi, my problem is car only crank but not start successful. I use EVO-ALL ( service #: 001A06-336)69 ), firmware: 79.12, installation docunment #8881, compustar CM6200, D2D. All function is working, programming is working, door lock, brake, Tach is working fine, I put a key in front of barrel will be start no problem, a red light is turn on and yellow light is on after that on EVO-ALL when I remote start engine. Any solution? By the way, I try idatalink is working perfect after that because you ready closed, but I need to find out the reason because I don't want giveup your product. Thanks.
Login to reply View 2 answer(s)

01/05/2014

 Toyota (Pts.)

0

2014 Toyota Camry G Key remote starter crank but not start

Hi, my problem is car only crank but not start successful. I use EVO-ALL ( service #: 001A06-336)69 ), firmware: 79.12, installation docunment #8881, compustar CM6200, D2D. All function is working, programming is working, door lock, brake, Tach is working fine, I put a key in front of barrel will be start no problem, a red light is turn on and yellow light is on after that on EVO-ALL when I remote start engine. Any solution? By the way, I try idatalink is working perfect after that because you ready closed, but I need to find out the reason because I don't want giveup your product. Thanks.
Login to reply View 2 answer(s)

12/01/2014

 Toyota William2 (1630Pts.)

2

2010 toyota venza with PTS will not start using compustar cm6200 and evo all

Evo All service# 001A06282907    Firmware 4.18

I installed the system using guide#8601. The evo all programed fine, the remotes, door lock and trunk work fine.

The tach and hood wires are not required with the evo all per fortin's guide.

I am having problems with the remote start.

I followed the fortin guide and everything was connected as instructed.

 

I press the remote start button on the remote and the car receives the signal to start. It flashes twice and turns on the dash cluster like is going to crank but it doesn't even try to crank. The odd thing is it turns the dash off and then on twice before giving up on the remote start process.  Is like it tries 3 times to start but doesn't crank.

 

Any ideas? 

 

I tried learning the tach, going tachless and changing the crank time but still did the same. 

 

UPDATE AS OF JAN. 12TH 2014:

I reseted the evo all and reprogrammed. Now the car cranks for 0.5 sec but does not start. Then it does the "dash on and off"3 times again. The remote flashes 3 times after failing to start(the error code for 3 flashes is "doors open(manual trasmissions only) but I cut the green loop inside the CM6200 module to make it automatic.

I tried increasing the cranking time to 1 and 1.5 sec. but still will not start and it only cranks for like 0.5 secs.

I did the tach learn process and was not succesful.

I think this is related to the tach and door pin wires not being connected as instructed in the guide, could it be?

Note: when I start the car with the key the yellow led on the evo all is the one on.

 

Thank you

Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue