Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

05/09/2016

 Toyota James G. (340Pts.)

1

Horn blowing constantly when Evo-All data link is disconnected

Installed an Evo-All + Prestige APS-57E system on a 2015 Corolla S. I also enabled the Evo-Alarm function. Everything works perfectly. But I accidently noticed what I believe could be a bad unit issue...

 

If I disconnect the datalink connector of the Evo-All, the horn constanly blows.

 

I even disconnected ALL connectors from the Evo-All and connected just the Evo-All by itself to the 20-pin harness and the horn started blowing again?? I have never seen this happen before and am worried that if the vehicles battery was ever disconnected, the client's horn would just start blowing? 

 

Somehow, the Evo-All has an internal ground signal inside itself? I tried reseting it as well. I also disconneted the horn connector from the steering wheel column and the Evo-All would still send a ground signal to the horn wire and blow it.

 

Conencting the data-link conector stops this from happening the the Evo works fine again. Is this just a bad unit?

Login to reply View 2 answer(s)

05/09/2016

 Toyota James G. (340Pts.)

1

Horn blowing constantly when Evo-All data link is disconnected

Installed an Evo-All + Prestige APS-57E system on a 2015 Corolla S. I also enabled the Evo-Alarm function. Everything works perfectly. But I accidently noticed what I believe could be a bad unit issue...

 

If I disconnect the datalink connector of the Evo-All, the horn constanly blows.

 

I even disconnected ALL connectors from the Evo-All and connected just the Evo-All by itself to the 20-pin harness and the horn started blowing again?? I have never seen this happen before and am worried that if the vehicles battery was ever disconnected, the client's horn would just start blowing? 

 

Somehow, the Evo-All has an internal ground signal inside itself? I tried reseting it as well. I also disconneted the horn connector from the steering wheel column and the Evo-All would still send a ground signal to the horn wire and blow it.

 

Conencting the data-link conector stops this from happening the the Evo works fine again. Is this just a bad unit?

Login to reply View 2 answer(s)

05/09/2016

 Toyota James G. (340Pts.)

0

Evo-All reseting itself -- and options

This is the same vehicle -- 2015 Corolla S. I have an Evo-All + Prestige APS-57E. Recently the client took the vehicle to the dealer and the battery was disconnected. After which the remote start no longer worked. I took a look under the dash and the Evo-All's red LED was constantly on. Trying to reset it didn't work as the red LED was always on.

 

I then connected the Evo to the Fortin program and upon selecting the "Evo-All Options" tab, Setting protection was turned ON (which I never did nor ever use) and once I turned that off to see the current settings, some options I had never selected where turned ON. Specifically, A1 --> A11 where now OFF and D2 --> E2 where now ON, as well as G3, G4, & H2.

 

Also, with out making any changes to the Evo-All nor flashing it, once I disconnected it from the Fortin program and went back to the vehicle to attempt a reset, the reset worked fine and the red LED wasn't constantly ON.

 

Any help appreciated. 

Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue