Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

27/09/2018

 Subaru Gaetan Roussel (260Pts.)

0

Which Start wire to use on Forester 2009 ?

I recently acquired a 2009 Forester. Using a Fortin Evo-All and a Crime Stopper RS2-G3 remote starter I cannot figure out which Start wire to use. 1) Your installation guide suggest the use of Start wires Ter 1 (White/Black) and 2 (White/Red) while the RS2-G3 connector only has one Start wire (Brown). How should I make the proper connection(s) ? 2) As well, the remote starter has two (2) Constant 12V (+) Input Red wires on its 6 pin power harness. Should both of them be connected to the RS2 (+) 12V white wire of the Forester Ignition harness ? PS. I see that on the Evo One installation you use a relay on the Start Ter 2 wire.
Login to reply View 1 answer(s)

27/09/2018

 Subaru Gaetan Roussel (260Pts.)

0

Which Start wire to use on Forester 2009 ?

I recently acquired a 2009 Forester. Using a Fortin Evo-All and a Crime Stopper RS2-G3 remote starter I cannot figure out which Start wire to use. 1) Your installation guide suggest the use of Start wires Ter 1 (White/Black) and 2 (White/Red) while the RS2-G3 connector only has one Start wire (Brown). How should I make the proper connection(s) ? 2) As well, the remote starter has two (2) Constant 12V (+) Input Red wires on its 6 pin power harness. Should both of them be connected to the RS2 (+) 12V white wire of the Forester Ignition harness ? PS. I see that on the Evo One installation you use a relay on the Start Ter 2 wire.
Login to reply View 1 answer(s)

12/12/2016

 Subaru Chad Cyr (950Pts.)

0

Wiring/Programming EVO-ONE w/ DSM300 SmartStart (2015 Subaru XV Crosstrek PTS)

Installed a EVO-ONE into my 2015 Subaru XV Crosstrek w/ Push-to-Start. I have no issues with the remote starter, bypass, locks, etc. Everything works great with a Fortin 2-way RF kit - which I am still temporarily using until I figure out how to get my DSM300 Smartstart to work. I didn't find the Smartstart guide particularly useful in regards to wiring it up to the EVO-ONE for my application. I had programmed the remote start to XL202 and grounded the gray D2D mode cable as per the Fortin guide. Can someone clarify if I am to use the white D2D connector that is included with the Smartstart's multi-connector harness and does it plug into the larger antenna port? Or do I need to make up a cable to go to the black Fortin Data-Link/Flashlink Port? Do I assume that I will have to power the Smartstart separately using its own 2-wire harness w/ 3-Amp fuse since the EVO-ONE isn't providing 12-Volts from the data ports? If so, do I remove the 12V power on my connection back to the EVO-ONE? I tried powering them separately and just leaving the data wires + ground, but I could not pair the Smartstart to the EVO-ONE; I sent a lock command which the Smartstart app said was successful during the pairing process as per the instructions I found, but I couldn't get the EVO-ONE to acknowledge the signal to pair the Smartstart. I hope someone can steer me in the right direction. Thanks - Chad
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue