Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

1

Does 2007 Nissan Maxima need the tach wire ran to the ECU/ECM to use "Tach Datalink only" on EVO-ONE?

I installed an EVO-ONE using the THAR-ONE-NIS2 T-harness in a 2007 Nissan Maxima w/Intellikey (obviously more connections were needed aside from the T-harness)... My question is: Do I need to run the tachometer wire from the Fortin 20pin connector to the tachometer wire at the ECU/ECM in order to use the "Tach Datalink only" option that's under the remote starter options via the FlashLink software. I thought some cars are getting this signal via the OBDII CANs. My Fortin install instrustions (Guide #17763) only had me connect to CAN-high and CAN-low on the OBDII connector. I already set the datalink protocol to "Fortin" as I thought this would be required. I realize I could just use "tachless" mode but I would prefer it starting using my tach signal. Tachless mode does work though(I used this mode to verify the bypass and remote start features were working). To be clear, I have only tried starting the car with "tachless only" mode and i have not ran a wire to the ECU/ECM tach line yet as im not sure if it is needed. So what do I need to do in order to use "Tach datalink only" mode? My guess is setting datalink protocol to "Fortin" and run the evo's tach wire to the tach wire @ the ECM.

1

Does 2007 Nissan Maxima need the tach wire ran to the ECU/ECM to use "Tach Datalink only" on EVO-ONE?

I installed an EVO-ONE using the THAR-ONE-NIS2 T-harness in a 2007 Nissan Maxima w/Intellikey (obviously more connections were needed aside from the T-harness)... My question is: Do I need to run the tachometer wire from the Fortin 20pin connector to the tachometer wire at the ECU/ECM in order to use the "Tach Datalink only" option that's under the remote starter options via the FlashLink software. I thought some cars are getting this signal via the OBDII CANs. My Fortin install instrustions (Guide #17763) only had me connect to CAN-high and CAN-low on the OBDII connector. I already set the datalink protocol to "Fortin" as I thought this would be required. I realize I could just use "tachless" mode but I would prefer it starting using my tach signal. Tachless mode does work though(I used this mode to verify the bypass and remote start features were working). To be clear, I have only tried starting the car with "tachless only" mode and i have not ran a wire to the ECU/ECM tach line yet as im not sure if it is needed. So what do I need to do in order to use "Tach datalink only" mode? My guess is setting datalink protocol to "Fortin" and run the evo's tach wire to the tach wire @ the ECM.

1

Does 2007 Nissan Maxima need the tach wire ran to the ECU/ECM to use "Tach Datalink only" on EVO-ONE?

I installed an EVO-ONE using the THAR-ONE-NIS2 T-harness in a 2007 Nissan Maxima w/Intellikey (obviously more connections were needed aside from the T-harness)... My question is: Do I need to run the tachometer wire from the Fortin 20pin connector to the tachometer wire at the ECU/ECM in order to use the "Tach Datalink only" option that's under the remote starter options via the FlashLink software. I thought some cars are getting this signal via the OBDII CANs. My Fortin install instrustions (Guide #17763) only had me connect to CAN-high and CAN-low on the OBDII connector. I already set the datalink protocol to "Fortin" as I thought this would be required. I realize I could just use "tachless" mode but I would prefer it starting using my tach signal. Tachless mode does work though(I used this mode to verify the bypass and remote start features were working). To be clear, I have only tried starting the car with "tachless only" mode and i have not ran a wire to the ECU/ECM tach line yet as im not sure if it is needed. So what do I need to do in order to use "Tach datalink only" mode? My guess is setting datalink protocol to "Fortin" and run the evo's tach wire to the tach wire @ the ECM.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue