Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

13/12/2022

 Chevrolet Dave Schmidt (160Pts.)

0

Ignition turns on but doesn’t start

I installed Crimestopper RS4-G5 in my 2003 Chev Silverado 1500 5.3L auto. I also installed the Fortin EVO-All and flashed it with the Fortin Flash-Link Updater 2. I've triple checked the wiring and triple checked the instructions when I programmed it. You hit the start button, it locks, ignitions turns on and just sits there and that's it. After that the yellow light and red light stays on on the EVO-ALL. Any help would be appreciated as this has been a long on going project.
Login to reply View 1 answer(s)

07/04/2022

 Chevrolet Dale appleton (180Pts.)

0

Wait Time

I've checked the status on my order and for three days it has beebn "Charged". How long before it gets shipped/sent? Accnt #: 50134; Sales Order #: 66321. Thank You.
Login to reply View 1 answer(s)

25/12/2019

 Chevrolet keith pearson (160Pts.)

0

Why are all three LED's blinking when the data link is plugged in..and not remote starting

Just need it to follow the #3 programming section
Login to reply View 0 answer(s)

16/12/2019

 Chevrolet Juan Becerra (390Pts.)

0

2001 Chevy Silverado 3500

On the website it says remote start is only supported for years 2003 and older. Would remote start work on the 2001 using the EVO ONE and the 2003 guide and just hooking up the wires as found on here? 

http://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.aspx

I also researched about the OBD wire and it appears to be the same.

Login to reply View 1 answer(s)

13/05/2019

 Chevrolet Harald Luksch (180Pts.)

0

Fortin EVO-ALL does not start Chevrolet Cruze 2011

I have installed and programmed the EVO-ALL in a 2011 Chevrolet Cruze. When I try to Start the engine with "3 times lock" I can see the blue LED correspond to when I push the lock button. It starts the process, unlocks the doors, ignition AC and radio go on, but does not crank. The procedure starts again - same result. Wat am I doing wrong? I also made a master reset and went through the complete programming and flashing again. And yes, C1 and D1 are activated .... No more ideas. Thanks in advance, Harald
Login to reply View 1 answer(s)

18/01/2018

 Chevrolet eric pozdal (130Pts.)

0

2011 chevy cruze step 5 will not change from yellow to red just stays yellow

2011 Chevrolet Cruze, standard switchblade key with ignition cylinder on column (not push to start). Using EVO-GMT1, with the t-harness. Only wire I have wired to the vehicle for now is the brown wire on the 5 pin connector, and that is spliced into the number 1 pin at the dlc for can bus. I can get programming to step 5. I have hit the program button 5 times, and it will flash 5 times in 4 sequences, and then stay on yellow when its done. When i turn the key it stays yellow and nothing happens. I do not want any other feature this offers, except 3 lock remote start. I have verified switching 0-3v at the brown terminal with key on, and have wired it multiple ways to verify it's not something I did. I was able to get it to turn red once, turned the key off, removed the key, waited 5 seconds, and turned the key back on and it stayed red. I am a gm technician and very familiar with these vehicles but I can not get this thing to program.
Login to reply View 1 answer(s)

14/07/2017

 Chevrolet Dywane Russell (130Pts.)

0

2014 Chevy Cruze won't start with evo-gmt1

The car won't start using the evo-gmt1 with the T harness
Login to reply View 1 answer(s)

22/11/2016

 Chevrolet Daniel DePass (130Pts.)

0

2012 cruze won't remote start with gmt1

Installed according to stand alone guide, activated stand alone using flash link 2. Module programmed o, but my car won't remote start with 3x lock. I grounded the dark blue wire on the 20 pin connector and nothing happened. When I grounded the yellow and black wire it started. No matter how slow or fast I press the lock button it won't start.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue