Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

28/10/2018

 Chevrolet Jeffrey Cabello (130Pts.)

0

Adding RF Kit to EVO One

I have a 2004 trailblazer with no OEM remotes. I would like to add remotes on. I purchased the EVO One, then purchased the FTX-64-2W. That came with a long cord and a T harness. Im not sure how to use the T harness? Anyway, I cannot get the EVO to go into programming mode to program remotes. I plug in the antenna, and the LED comes on then goes off. Nothing else happens. I tried the instructions and getting into valet mode, but the antenna LED does not flash. Currently flashed for the 2004 trailblazer, with updated firmware. No options in flash link to enable/disable rf control. Any help suggested. Thanks. Also, when it says ignition on, does that mean to start the car or put the switch in the position right before starting the car?
Login to reply View 2 answer(s)

28/10/2018

 Chevrolet Jeffrey Cabello (130Pts.)

0

Adding RF Kit to EVO One

I have a 2004 trailblazer with no OEM remotes. I would like to add remotes on. I purchased the EVO One, then purchased the FTX-64-2W. That came with a long cord and a T harness. Im not sure how to use the T harness? Anyway, I cannot get the EVO to go into programming mode to program remotes. I plug in the antenna, and the LED comes on then goes off. Nothing else happens. I tried the instructions and getting into valet mode, but the antenna LED does not flash. Currently flashed for the 2004 trailblazer, with updated firmware. No options in flash link to enable/disable rf control. Any help suggested. Thanks. Also, when it says ignition on, does that mean to start the car or put the switch in the position right before starting the car?
Login to reply View 2 answer(s)

17/01/2015

 Chevrolet Andrew Pearson (170Pts.)

0

No heated seats / rear defroster at or below 32 degrees

Have a 06 Trailblazer, with the INTSL- + installed. I have yet to see the heated seats or rear defroster turn on when the temperature is at 32 or below. Was I missing something when I hooked it up. I didn't use datalink when hook up to the alarm.
Login to reply View 1 answer(s)

13/10/2014

 Chevrolet Michael Armentano (130Pts.)

0

Is the Avital 4103 compatible with FORTIN INT-SL+?

I purchased an Avital 4103 and a FORTIN INT-SL+. The D2D cable from FORTIN does not fit the 4103. Am I going to have to use W2W? Or is there a way to utilize the D2D with the 4103? (2008 Chevrolet TrailBlazer)
Login to reply View 1 answer(s)

24/02/2014

 Chevrolet Bryan Short (140Pts.)

1

2007 Trailblazer, remote start shutdown after 10-12 seconds, recommended fix doesn't work

I looked through previous questions and couldn't find the answer.......I have a 2007 Trailblazer with a Bulldog RS82 remote starter. The INT-SL is in datalink mode and has been working perfectly for over 4 years, operating the parking lights, heated seats, rear defrost, etc. Just the other day my vehicle started shutting down about 10 seconds after startup via remote starter. I saw the bulletin about the false positive on the brake signal being communicated to the remote starter unit, so I tried the fix recommended there of grounding the green wire. However, doing this only seemed to disable the security bypass as the vehicle would then just crank and crank with no ignition. I disconnected the INT-SL and reset it several times to see if I could get any different result, but didn't. I did isolate the issue to the INT-SL by ruling out the Bulldog unit as the problem. I did so by letting the remote starter start the vehicle, then unplugging the 4 wire connector from the INT-SL before the 10 second shut down, and the remote starter continued to keep the vehicle running. The INT-SL is running firmware v. 3.01. I really don't want to have to try to hard wire into the parking lamps and lose the heated seats/rear defrost features. Any ideas on what else may be going wrong, or how to fix it? Please let me know. Thanks....
Login to reply View 1 answer(s)

24/01/2014

 Chevrolet Jay B (140Pts.)

1

Why does my INT-SL+ not turn on the rear defrost in my 2008 Trailblazer?

I installed a INT-SL+ into my trailblazer along with a Ultrastart 1280pro remote start unit connected via data wire. All works fine except that the INT-SL+ will not turn on my rear defrost automatically when remote started. The vehicle fitment chart says it will turn on rear defrost when the engine temp is 0C or below... it's been -10F most of the week but my rear defrost has never automatically turned on? did I miss something?
Login to reply View 1 answer(s)

13/01/2014

 Chevrolet Andrew Pearson (170Pts.)

1

Does the INT-SL+ monitor all the doors on 06 Chevrolet Trailblazer or just the fronts D/P

Hello, I purchased an INT-SL+ in to install on my 2006 Chevrolet Trailblazer. It says that it monitors the door status however it does not detail if it is all of the doors, inlcluding tailgate of if it is only the front 2 doors. I have been told that most modules wil only monitor the front 2 doors. Can you please let me know if I will have to run wires to all the doors so that the alarm will go off if either of them are open.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue