Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

TMPS error 2015 Audi A3

I installed the Evo one with the T harness on a2015 Audi A3 with a push to start. When starting the vehicle with the remote start or the push button start the vehicle has the following errors: Stabilizer control ECS malfunction, TPMS error, hill assist disabled.

0

TMPS error 2015 Audi A3

I installed the Evo one with the T harness on a2015 Audi A3 with a push to start. When starting the vehicle with the remote start or the push button start the vehicle has the following errors: Stabilizer control ECS malfunction, TPMS error, hill assist disabled.

0

Fortin Evo-All 2011 Audi A3

I'm trying to do a standalone installation of the EVO-ALL on a 2011 Audi A3. All of the wires are connected correctly and I made sure they are making a good connection. I held the prgramming button down and the lights started alternating. I relaesed the button when only the blue LED was lit. I then plugged in the 20 pin, connector, followed by the 6 pin connector, followed by the 5 pin connector. The LED remained blue throughout this process. I then turned the ignition to on. The bule LED went out, then started flasing after a few seconds. I turned the ignition off and the blue LED went out. When I press the factory remote 3X to start the vehicle, the lights flash and the dash lights come on, but it doesn't try to start. It does the same thing a second time and then the EVO-ALL turns off. However, if I sit inside the vehicle and press the brake, it will start the car, but it only runs for 1 or 2 seconds before shutting down. On this particular vehicle, although it uses the regular keyed ignition switch, you still have to press the brake to start the vehicle. Is there another connection that needs to be made for this to work properly? Thank you, Jason

0

Fortin Evo-All 2011 Audi A3

I'm trying to do a standalone installation of the EVO-ALL on a 2011 Audi A3. All of the wires are connected correctly and I made sure they are making a good connection. I held the prgramming button down and the lights started alternating. I relaesed the button when only the blue LED was lit. I then plugged in the 20 pin, connector, followed by the 6 pin connector, followed by the 5 pin connector. The LED remained blue throughout this process. I then turned the ignition to on. The bule LED went out, then started flasing after a few seconds. I turned the ignition off and the blue LED went out. When I press the factory remote 3X to start the vehicle, the lights flash and the dash lights come on, but it doesn't try to start. It does the same thing a second time and then the EVO-ALL turns off. However, if I sit inside the vehicle and press the brake, it will start the car, but it only runs for 1 or 2 seconds before shutting down. On this particular vehicle, although it uses the regular keyed ignition switch, you still have to press the brake to start the vehicle. Is there another connection that needs to be made for this to work properly? Thank you, Jason

1

Stop working Audi A3 2011

I install evo-all and a remote starter in a 2011 Audi a3. It works fine. 2 days after the remote doesn't work anymore. I tried it and manage to make it works with the key near the cylinder. Can the evo-all loose its key programation ? Can i see what is wrong looking at the colored led on the EVO-ALL. Should i reset it and reprogrammed it? Do i need to plug it back to the flash-link programmer? Thank you

1

Stop working Audi A3 2011

I install evo-all and a remote starter in a 2011 Audi a3. It works fine. 2 days after the remote doesn't work anymore. I tried it and manage to make it works with the key near the cylinder. Can the evo-all loose its key programation ? Can i see what is wrong looking at the colored led on the EVO-ALL. Should i reset it and reprogrammed it? Do i need to plug it back to the flash-link programmer? Thank you

0

Evo-all 2006 Audi A3 with CM7200 controller not seeing tach through Data

I am installing a cm7200 starer in a 2003 Audi A3 and am using the data port for connectiong the two units. I cannot find if there are any issues with compatibility between these two units IE, two way data. I can't seem to get tach to program or the unit to go into reservation mode for standards. i am guessing the reservation issue is something to do with the tach issue.

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue