Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

11/01/2015

 Dodge scott landry (150Pts.)

0

after install I relized i have 4.18 version and i need 4.06 how can i change it?

how can i get evo all 4.18 version to work on 2004 dodge caravan
Login to reply View 1 answer(s)

22/12/2014

 Dodge Jesse Hir (680Pts.)

0

Evo-Chr T1 can i use it for 14' Caravan??

I have a old Evo-Chr T1 still in stock and ran out of harness 4's. Is it possible to use this set up in a 14' Caravan? If so, which firmware should it be updated too?
Login to reply View 1 answer(s)

23/10/2014

 Dodge mark olinyk (130Pts.)

0

caravan-programming 001A06-360033

I am using the autostart remote starter with the fortin evo all bypass. I have the remote starting working except for programming the bypass. I am using the d2d connector to share data from the autostart to the fortin. Following the instructions of plugging in the 4 wire connector and holding the programming button, i stop at the blue LED. I connect the 20 pin , then the 6 red pin connector. The blue LED then stays on and i turn the igntion switch on. The blue LED goes out and then nothing happens. I have done this many times and the result is the same. The bypass will not learn the skim code as it is described in the instructions . I am at a loss . PLease help . Thanks.
Login to reply View 2 answer(s)

23/10/2014

 Dodge mark olinyk (130Pts.)

0

caravan-programming 001A06-360033

I am using the autostart remote starter with the fortin evo all bypass. I have the remote starting working except for programming the bypass. I am using the d2d connector to share data from the autostart to the fortin. Following the instructions of plugging in the 4 wire connector and holding the programming button, i stop at the blue LED. I connect the 20 pin , then the 6 red pin connector. The blue LED then stays on and i turn the igntion switch on. The blue LED goes out and then nothing happens. I have done this many times and the result is the same. The bypass will not learn the skim code as it is described in the instructions . I am at a loss . PLease help . Thanks.
Login to reply View 2 answer(s)

08/09/2014

 Dodge Grease Monkey Tuners (1230Pts.)

0

2014 Dodge Grand Caravan - Not Programming

Could you please verify if the 2014 Grand Caravan will actually work with the EVO-ALL as stand alone remote starter? We have done two of the 2012 model last year and it worked great. We have tried installing it into a 2014 model this weekend and the EVO-ALL will not program at all (when we put the key on ign, the blue led will turn off - no flashing - and it'll turn back on when we pull the key out, thats it). Triple checked my wiring (i mean there were only about 5 - 6 wires needed to be hooked up into the ignition harness; made sure that the CAN Low and CAN High were right colors and were not reversed) and also tried two different EVO-ALL modules and harnesses The service # of the first EVO-ALL we have used is 001A06 349006 and I could give you the second one if needed Please assist and verify if it actually is compatible on the 2014 Dodge Grand Caravan. I have set up a time to go into the customer's workplace and try this again today. Thanks
Login to reply View 1 answer(s)

01/05/2014

 Dodge (Pts.)

0

2010 Caravan not programing

I have a evo-all, im trying to install in my works 2010 Dodge Caravan, I hook it up but it wont program to the van, I have the wiring done correctly, I can start and drive, just wont program to use the Remote Start, I took it to a local installer and had the Evo-All programmed with "Option 15" but when he was in the software, Option 15 was something todo with the Lock and I think 36 was the 3x Remote Start Option, He said they where already on and reflashed it to make sure. But I cant get it to program to the 2010, the Blue light just keeps flashing slowly after I put the van into ON after doing the programing steps.
Login to reply View 1 answer(s)

30/01/2014

 Dodge Jacques Caron (140Pts.)

1

D

D
Login to reply View 1 answer(s)

14/01/2014

 Dodge David Dohle (140Pts.)

1

2008 dodge caravan wont start then just honks

I installed evoall with prostart lcpro-1. Connections are correct and sound. When remote button is pushed, lights activate and relays are heard. Then evoall light goes red and van honks. Does not start. has anyone seen this before?
Login to reply View 1 answer(s)

30/12/2013

 Dodge Alan Eastman (140Pts.)

1

Access to 2012 Grand Caravan Ignition Barrel

Can you provide some direction on how to access the Ignition barrel of a 2012 Dodge Grand Caravan SXT? I lossened (not removed) the lower dash panel below the steering wheel thinking that I would have the access needed. I was not able to access the barrel and did not want to start prying off the small trim panel that is around the barrel where the the key is inserted without first asking for help. Thanks.
Login to reply View 1 answer(s)

15/12/2013

 Dodge johan loewen (180Pts.)

0

i am unable to program the bypass to work with my 2006 dodge caravan

hello i have a fortin evo-all interface module and when i press the programming botton and plug it in the blue light comes on and when i turn the key on all the lights go out and it wont let me program the module. the service # is 001a06 222997 firmware version 4.18 hardware version 6. i was wondering if you could tell me if this is the wrong module or help me in figuring out why it wont program
Login to reply View 1 answer(s)

13/12/2013

 Dodge Richard Sicat (200Pts.)

0

is their any desired wattage for 1k ohm resistor that will be used in dodge caravan2013 for the harness?

desired wattage for 1k ohm Resistor that will be used for dodge caravan 2013 for the Harness? thanks
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue