Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

23/01/2022

 Acura nader dana (280Pts.)

0

Difficulty in programming EVO-one for Acura RL 2010

Firmware is updated to 73.[38] . When I insert the 6 pin connector the red light does not become solid for me to release the programming button. It keeps alternating the blue ,red, yellow and blue&red and I have done disconnecting and redone step one many times with no result.How can I fix it?
Login to reply View 1 answer(s)

16/05/2021

 Acura Luis Sanchez2 (950Pts.)

0

RFK942 not working after disconnecting and reconnecting the car battery

After getting the RFK942 working I did some maintenance on the car. I disconnected the battery to perform the maintenance required and after reconnecting the battery I attempted to lock the doors with the RFK942 remote. The remote sent the signal but doors did not lock (LED turned red). I thought that perhaps the antenna needed to be reprogrammed so I attempted to perform the programming procedure again. The antenna would not program (no blue LED) so I connected it to the Flashlink Manager to see if something had been turned off. The Flashlink Manager did not recognized that the antenna was connected. From this I am gathering that the antenna was damaged when I reconnected the car battery. Is this possible? If so, what can I do to prevent this from happening again? Would a different RF kit work better (for example the RF642W)?
Login to reply View 1 answer(s)

06/04/2021

 Acura Luis Sanchez2 (950Pts.)

0

EVO ONE does not see RFK942

Good day to you. I am having problems programming the RFK942 to the EVO ONE (installed in my 2010 Acura TL with Push-to-Start). When I connected the antenna to the module (using only the antenna cable the RF kit came with) the blue LED on the RF antenna never turned on. After several attempts, I decided to remove the EVO ONE and connect it to my computer (running Windows 10) using the Flashlink Updater (running the latest firmware). The Flashlink Updater could not detect the EVO ONE (and the EVO ONE LEDs never illuminated). I thought that perhaps the Flashlink Updater was inoperative but when I connected an EVO ALL and two RFK942s to the Updater, I discovered that the Updater is functioning properly. I just programmed the EVO ONE a week ago and had no issues then. In fact, the module remote starts the vehicle (Lock 3x on OEM key fob). Any help would be greatly appreciated.
Login to reply View 1 answer(s)

30/03/2021

 Acura Luis Sanchez2 (950Pts.)

0

RF Kit Acura TL

I am installin the RFK942 to my 2010 Acura TL.  Will there be any additional wires that will need to be connected at or to my EVO ONE (besides the cable from the antenna)?  Are there any features that need to be turned on on the Flashlink Updater and if so, where will they be found?  Thank you.

Login to reply View 1 answer(s)

28/03/2021

 Acura Luis Sanchez2 (950Pts.)

0

Check Keyless Message

The installation and programming of the EVO ONE on the 2010 Acura TL (Push to Start) went well. I am able to start the vehicle, and, as expected, the engine shuts off when the door is opened (which is a bummer). My question concerns a message on the instrument panel. When I remote start the vehicle the "Check Keyless Starting System" (with an amber key with an exclamation point) is displayed. Is this normal? My second question iis about adding an RF kit. Will the RFK942 RF kit work with the EVO ONE on this car? Thank you in advance for your help.
Login to reply View 1 answer(s)

23/03/2021

 Acura Luis Sanchez2 (950Pts.)

0

2010 Acura TL Push Start Evo One will not program

While installing the EVO One to my 2010 Acura TL (with Push-to-Start) I found that several of the wire colors called out by the installation (REV:20191022, Guide 19411) and the Wire Color guide did not match what the car has (on gray 32 pin connector and blue 36 pin connector).  I proceeded by connecting at the specified locations shown on the diagram.  Once the connections were completed, I attempted to program the module (which was updated and programmed with the Flash Link Updater).  Step 1-4 went OK, however, when I got to step 5 (Do not press the brake pedal.  Press the Push-to- Start button twice to turn on the ignition--  The RED LED will flash rapidly 10x times. -- Key bypass programmed. --The BLUE LED will flash rapidly. --CAN-Bus programmed.), the red LED extinguished and I could not complete the programming.  I tried this several time with the same results.  Your help with this issue will be greatly appreciated.

Login to reply View 1 answer(s)

13/12/2020

 Acura Darren Martin2 (130Pts.)

0

Immobilizer wire color and pin location do not match diagram downloaded from fortin website.

SL3 - 2010 Acura TL 3.7 - Standard key
Login to reply View 1 answer(s)

24/02/2020

 Acura MOUSSA SLEIMAN (180Pts.)

0

2010 Acura TSX, what do i need in all?

hello, i have  a 2010 acura TSX, i saw the evo all and evo one but ive had a 2010 dodge ram that i fought a pre-programmed evo which was called "Fortin Evo-chr.t4" and just bought the wire harness with that and it worked very easily. Im wondering if there is such a thing for my acura without havin to buy the evo-all or evo-one and program them, would the HONDA-SL3 be what i'm lookin for? EVO-RIDE? EVO-KEY? not sure what all these options are? thank you

Login to reply View 1 answer(s)

13/01/2020

 Acura Owen Scott (130Pts.)

0

Which wire on the THAR-HON-A2 connector needs to be cut for a 2010 Acura MDX EVO-ONE Installation?

The installation guide for the EVO-ONE on a 2010 Acura MDX states that a wire has to be cut on the green male side of the THAR-HON-A2 connector, and that wires D1 and D3 are connected to the two newly created ends of the cut wire. Which wire am I to cut? Any and all help is greatly appreciated. Thank you!
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue