English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

07/01/2024

 Mazda elloran97 (130Pts.)

0

EVO-One for 2011 Mazdaspeed 3 - Remote start starts the vehicle but immediately shutsdown after 1 second.

After I put my vehicle in ready-mode for my manual, push-to-start vehicle, my car will remote start properly, however, it immediately shuts off after about 2 seconds. Parking lights don't show any indication on why it shutdowns either. What could be the issue? I also noticed that the wiring diagram for installation have flipped wiring colors for 7A (Back Clutch Switch 2) and 7B (Front clutch switch 1). It says the Back clutch switch should have 2 cables, a WHITE and a BLACK cable, however, in reality it has a GREY and BLACK cable. Same thing with the Front clutch switch; diagram says it should have a GREY and BLACK cable but it they're WHITE and BLACK in my car... I have tried both of these wirings actually, and the problem still persists. Even if this is not the cause of the problem, which one is correct?
Connectez-vous pour répondre Voir 1 réponse(s)

11/02/2022

 Mazda Nick Johnston (130Pts.)

0

Mazda 3 5dr (hatchback), Manual Transmission, RFID in keyfob.

Vehicle type:

2011 Mazda 3 (5 door/hatchback), manual transmission, key to start. Integrated key/keyfob (lock,unlock,panic), keyless entry w/RFID chip for factory immobilizer system.

Wants:

Remote Starter, Factory Immobilizer bypass, OEM keyfob (lock-lock-lock to start), alarm functionality optional at a later date.

 

Ready to install Evo-One, Flash-Link and RFK442.

 

Few problems so far (have not started install yet or any flashing of Evo-One vehicle specific Bypass settings):

   I see a conflict between Fortin wiring guide #80431 and #29661. Same vehicle, Mazda 3 - Axela 2010-2013, but two different wiring schemes.  Which one is the more correct one, or, can you suggest a better one?

 

   On Fortins website, for this vehicle it states 'Automatic Transmission Vehicles Only'  In Guide #80431, pg 5, it gives Manual Transmission programming instructions as does with Guide #29661 pg6, both of which conflicts with Fortins webpage.. 

 

   With Flash-Link v4.51, when entering vehicle info, there is NO option for Manual Transmission.

 

   In Guide #94011, pg11 (Function #20) Engine Supervision: Tachless, Analog or Data-Link.

I see there is no option for a true Analog input; i.e Vacuum switch, or hardwire to coil (or even a much older method of wraping 6in of stripped wire around a spark plug wire). Is there not a true analog tach input?

 

   I also cannot seem to anything at all about 'clutch bypass'

 

So, Manual Transmission? Yes or No? 

 

   For the Flash-Link Manager software, the v4.51 does not reflect the instructions I found for possibly older software instructions of Flash-Link Manager User Guide v1 #68731, any updated Guide #?

 

 

Flash-Link Manager software v4.51 (when I click on Settings in the software it shows v4.51-1.1.15)

Flash-Link V4 module, Hardware V5, Firmware v4.08

Evo-One module date 07/2021, s/n (PM me for serial number), Firmware: for a moment it showed v1.25 then within a few seconds dropped down to v1.01

 

Thanks, Nick.

Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer