English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

24/03/2022

 Chevrolet crispyrp69 (420Pts.)

0

Runs for 20 seconds then stalls

06 Impala standard key and regular install. Runs for about 20 then stalls out. Dosent seem to shut down, more of a stall out.Only starts once and then light flash 3 times
Connectez-vous pour répondre Voir 2 réponse(s)

24/03/2022

 Chevrolet crispyrp69 (420Pts.)

0

Runs for 20 seconds then stalls

06 Impala standard key and regular install. Runs for about 20 then stalls out. Dosent seem to shut down, more of a stall out.Only starts once and then light flash 3 times
Connectez-vous pour répondre Voir 2 réponse(s)

23/12/2020

 Chevrolet brad boyd (130Pts.)

0

evo all 2015 chevy trax step 4 yellow only blinks 4 times then goes yellow and red solid

teck support says the brown wire is not making a good connection so i checked and everthing is making good contact and from the obd2 port terminal one (green wire i am curenly plugged rite into it to make sure that is not the issue. checked with meter and the connection is reading .5 of an ohm. so that is not an issue any more if it was. just seeing if anyone know where to go from here thanks
Connectez-vous pour répondre Voir 2 réponse(s)

23/12/2020

 Chevrolet brad boyd (130Pts.)

0

evo all 2015 chevy trax step 4 yellow only blinks 4 times then goes yellow and red solid

teck support says the brown wire is not making a good connection so i checked and everthing is making good contact and from the obd2 port terminal one (green wire i am curenly plugged rite into it to make sure that is not the issue. checked with meter and the connection is reading .5 of an ohm. so that is not an issue any more if it was. just seeing if anyone know where to go from here thanks
Connectez-vous pour répondre Voir 2 réponse(s)

31/12/2019

 Chevrolet Anthony Martin Martin (130Pts.)

0

Do I need a separate remote starter module for 3x remote start on my 2005 silverado 2500?

Do I need a separate remote starter for 3x lock on my 05 silverado 2500 standard;key. not sure how to wire it with standalone application as my schematics show an additional remote start module.
Connectez-vous pour répondre Voir 1 réponse(s)

21/11/2019

 Chevrolet Brian Kells (220Pts.)

0

12v wire on evo all 2018 silverado

In the instructions for a stand alone install on a 2018 Silverado it shows to cut the 12v and ground wires and connect them to the vehicle source if no RF kit is used. Is this necessary? I intend to use a fortin 2 way rf kit in the near future. Also there are not clear instructions on hooking up the valet switch. Where does this go? Also can i setup the rf kit function when i first flash the module and then hook up the rf kit later or will that prevent the 3x lock function from working on the factory remote? Thanks
Connectez-vous pour répondre Voir 1 réponse(s)

19/10/2016

 Chevrolet James Cooke (130Pts.)

0

Data link for 2008 trailblazer

I'm not getting data tach or park light through the data link. I have the "evo-all, firmware 4.06" and my starter is "excalibur al 1860 edpb v2"
Connectez-vous pour répondre Voir 1 réponse(s)

10/11/2015

 Chevrolet Scott St.Denis (430Pts.)

0

EVOALL GMT1 won't program on 2014 Malibu

Sevice#001A06440829 yellow light comes on, I pushed the program button, red light stays on solid, turn key on red light goes off and comes back on then I shut key off take out of ignition put the key in turn to on position red light flashes 4 times stays on solid nothing else happens. Programmed to decrypt the key, reset EVO ALL, tried all kinds of software from 4.18 all the way to newest. Nothing works. Tried to call waited on hold for 2 hours with customer waiting. What are my options now?
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer