Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

02/12/2023

 Chevrolet Denis Hamel (130Pts.)

0

2020 Trax

2020 trax, using the GMT-1 All hooked up, All programed, reconnected to the car and will not work. No lights come on, Red,Yellow, or Blue. Turn the ignition on with the key and get a yellow light.
Login to reply View 1 answer(s)

14/11/2021

 Chevrolet R & P Electronics (280Pts.)

0

2019 Chevy Trax Won't RStart after install

So we have installed a Evo All in this car, Using it as a stand alone RS, The Car will light up everything after 3X on factory remote, but then the dash goes dead, with a CEL light (radio playing) Turns off.... EVO ALL tries agian, and fails... 4 Red light flash on unit... Checked my cables... Everything hooked up correct - Hood Disabled in programing, (Parking lights NOT hooked up at the moment) Removed the flash, and tried to reflash a couple times, and ended up locking myself out (I need cleared please Fortin) Any advice here please help out... Thank you
Login to reply View 1 answer(s)

29/12/2020

 Chevrolet Ealouise Luke (130Pts.)

0

doors won't unlock with remote after remote start

2017 chevy trax
Login to reply View 1 answer(s)

23/12/2020

 Chevrolet brad boyd (130Pts.)

0

evo all 2015 chevy trax step 4 yellow only blinks 4 times then goes yellow and red solid

teck support says the brown wire is not making a good connection so i checked and everthing is making good contact and from the obd2 port terminal one (green wire i am curenly plugged rite into it to make sure that is not the issue. checked with meter and the connection is reading .5 of an ohm. so that is not an issue any more if it was. just seeing if anyone know where to go from here thanks
Login to reply View 2 answer(s)

23/12/2020

 Chevrolet brad boyd (130Pts.)

0

evo all 2015 chevy trax step 4 yellow only blinks 4 times then goes yellow and red solid

teck support says the brown wire is not making a good connection so i checked and everthing is making good contact and from the obd2 port terminal one (green wire i am curenly plugged rite into it to make sure that is not the issue. checked with meter and the connection is reading .5 of an ohm. so that is not an issue any more if it was. just seeing if anyone know where to go from here thanks
Login to reply View 2 answer(s)

08/01/2020

 Chevrolet William Gorzelsky (130Pts.)

0

Solid Red LED immediately after plugging in Data-Link Wire

I have an EVO-ALL unit with T-Harness THAR-GM1. I went through the initial steps for programming, programmed the unit using the Flashlink Manager software. Reinstalled into the car, remote start did not work. Attempted to redo programming. Unit began displaying a solid Red LED. I held in the programming button and inserted the Data-Link wire and it immediately displayed the solid Red LED again. I continued to hold the button in for several minutes and the Red LED remains lit. I then tried to reconnect it to Flashlink Manager, and it detects it. I tried to reinstall the firmware and it installs. I take it back to the car to try programming again, and again i received the solid Red LED immediately. I am at a loss as to what the problem can be.
Login to reply View 1 answer(s)

09/12/2018

 Chevrolet Martin Cowger (130Pts.)

0

2019 Trax

looking to install the EVO-GMT1 system on a 2019 Trax LS will there be an update or just program as a 2018 being there is no change in the vehicle between 2018 to 2019 ?
Login to reply View 1 answer(s)

21/11/2016

 Chevrolet John Chamberlin (150Pts.)

0

Chevy Trax 2014 Takes 4 Button Pushes To Start

I have a successfully working install for 2014 Chevy Trax with T harness. Current firmware updated and used the flash updater to customize for the specific car. Enabled the 3 lock button press OEM remote start option in the menu, saved those settings to the unit. Followed the key on/off proceedures to program the unit successfully. For some reason, it takes 4 lock button pushes to get the starter to engage. Sometimes it take 2 sequences of 4 button pushes also. So sorta scratching my head. The unit is presently attached under the dash and I dont have the service number for the unit. If it's critical, I can ge the number however.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue