Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

When i try to remote start after install a blue light flashes on module but Jeep does not start

I finished installing and programming my remote start on my 2020 Jeep Wrangler w/o keyless entry. I have the after market remote start remotes and when I go to start it a blue light flashes once on the module but the Jeep does not start. Dash screen light comes on and so does the lights by the gear selector but that’s it.

0

Jeep Grand Cherokee 2015 blue light wont come back on after turning the ignition off

this is a push to start jeep I followed the steps: 1. plug in holding button 2. let go on blue and then turn the igntion on 3. after i press the button when the igition is on the blue light shuts off 4. turn the igniton off and then it is supposed to be red and blue flashign but that hasnt happened for me

21/11/2020

Jeep Phil D (180Pts.)

0

Jeep Liberty wont start

I bought my Evo-all for a 2009 Jepp Liberty and was told it was going to be flashed for it. I connected the chrt5 wires, yellow to yellow and purple to green with red tracer. I did the programming as per youtube and all the steps worked great. Now when I press lock 3 times it doesnt start. The blue light flashes when i press the lock button but no start. I suspect it hasnt been flashed. Is there a way to tell if thats the case before I buy the flashlink? or do I have other issues?

21/11/2020

Jeep Phil D (180Pts.)

0

Jeep Liberty wont start

I bought my Evo-all for a 2009 Jepp Liberty and was told it was going to be flashed for it. I connected the chrt5 wires, yellow to yellow and purple to green with red tracer. I did the programming as per youtube and all the steps worked great. Now when I press lock 3 times it doesnt start. The blue light flashes when i press the lock button but no start. I suspect it hasnt been flashed. Is there a way to tell if thats the case before I buy the flashlink? or do I have other issues?

0

EVOALL will not learn key code in Jeep Gladiator

Hello. When I power up the EVOALL, I get to where the blue light is solid and when I turn the ignition on, the blue light shuts off. The module is then supposed to flash blue rapidly to learn the key code. The module lights do not turn on or flash. This is a stand alone EVOALL with the T harness. I am at a loss. I checked all of my connections. I have the latest firmware via FLASH-LINK. Thanks in advance.

0

EVOALL will not learn key code in Jeep Gladiator

Hello. When I power up the EVOALL, I get to where the blue light is solid and when I turn the ignition on, the blue light shuts off. The module is then supposed to flash blue rapidly to learn the key code. The module lights do not turn on or flash. This is a stand alone EVOALL with the T harness. I am at a loss. I checked all of my connections. I have the latest firmware via FLASH-LINK. Thanks in advance.

0

EVO-ALL in 2004 Jeep Liberty will not program

2004 Jeep Liberty, no factory alarm, with transponder key. EVO-ALL is installed with a Compustar CS800-S. Used installation guide #3317, Connection #1, Program #1. Firmware flashed is 74.[38]. I can get the bypass to enter program mode (solid blue LED). When turning the ignition key to ON, the blue LED turns off and nothing else happens. The guide says the LEDs are supposed to turn on and off BLUE - RED - YELLOW in sequence, taking up to one minute. I waited 5 minutes with no lights turning on. Any advice?

0

Pairing. No flashing blights to pair key

Hello. I 've purchased the evo-all remote starter. I've purchased the flash link. Updated the software from the online app. When I plug it in I get the solid blue light, plug all the other connectors, key in ignition to run position, but I do not get the lights flashing to pair the key to remote starter. What is it that i'm doing wrong. Followed all the steps even checked on youtube and I get nothing. Please help. Thanks

0

Blue Light Flashing After Programming

I have a Jerp Commander 2007, followed instructions. Added yellow cable, everything went smooth with programming, till the point where u take key out and hit lock button. After that blue led light just flashes and won't start the vehicle. Any ideas?

11/04/2015

Jeep J Whit (130Pts.)

0

Blue light won't flash with key at "ON" position!?

I can not get the blue light to flash when I insert the key in the ignition and turn to "ON" position. Are there any other wires I need to wire-in manually for this product to work or should I be able to simply "plug&play"? I have a 2015 Jeep Compass and only want to install stand alone remote start function.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer