Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2018 Ford f150, why no blue flashing light after programming

2018 Ford f150 standard key without keyless entry, evo-on, T-harness FORT2, firmware 4.01, not getting the blue flashing light or red yellow alternating at step 8 of bypass programming procedure, getting the red flashing light 1 flash per second after the last step where ignition turns on and off by itself.

0

2017 EvoOne with TharFor3 T harness, blue light won't blink on programming

Thank you in advance for any help! I am a long time using of the EVO ALL and have done a few EVO ONE. A bit stumped on my 2017 F150 though. Using EVO ONE with the THAR FOR 3 harness. All plugged in. Following wiring diagram for the A1 and A16 (put them together) on the white 20 pin connector. When I go to program it, I can't get it to "blink blue". Therefore, I can't get any further in the programming procedure. Followed the directions in the Guide. What could I be missing? Joe

0

RFK 411 Not flashing blue rapidly when trying to program new keys

I bought Fortins Rf Kit (rfk 411) after being able to program the fobs to the antina i was able to start my vehicle but only start it i wasn't able to unlock the car or lock the car with the fobs having this issue i decided to factory reset my evo and start from scratch and being able to reprogram the keys in order to reslove this issue. I have factory reseted my evo three times in order to get to where i need to program the keys. My current issue that im having now is when i go to program the keys. I plug in the antina and everything to the evo. The antina flashes blue once but when i go to put the evo in progamming mode and put the key in the igntion the antina should be flashing rappidly but its not. The antina only flashes when the vehicle is armed

0

Ford Focus 2017 No flashing blue light on initial step to program

I was sent an EVO all that was preprogrammed. During first attempt, something went wrong, and I think by whole unit had the programming erased. I bought my own Flash Link updater, and loaded the settings based on standard questions. I believe I have everything right, but when I take the module to the car and hold down the program button and plug in the data cable, I only get the solid red light. No alternating blue, yellow, red. I did get them on my first attempt, but not after my reprogram. Can anyone help?

0

I have the evo rs with the tharfort1 for my 2012 f150 can't get it to work

I also have the flashlink updater, unlocked the remote start in the truck, and have 2 active keys and it will not work

0

Programming failure 2015 Ford Fusion standard Key w/ standalone + THAR-FOR2

Following instruction 59421 to install a stand-alone system with THAR-FOR2, I get to step 9 in the key bypass programming section. The vehicle's ignition turns on, but the blue light never flashes rapidly. I've confirmed that the firmware is 71.46, and the 3 wires (Light Blue, Light Blue/Black, and Yellow) that come from the T-harness are properly crimped to the wires going to pins A20, A10, and A1. (crimped, and applied adhesive lined heat-shrink) The CAN connections were connected to the wires at the pins as depicted on page 4 of the instructions - I noticed an error in the instructions, pin 20 on the diagnostic connector had a solid blue wire, rather than White/Blue. This wire was going to pin 20, and was twisted with the white wire on pin 19. To confirm proper connections, with the connector unplugged from the Evo All, I measured resistance between C1 & C2 to be 62ohms, and between C3 & C4 to be 61ohms - consistant with a standard CAN network. I've tried switching C1 with C2, I've also tried switching C3 with C4 - no improvement. Any help to get past step 9 will be appreciated.

0

blue light doesnt come on after programming both keys

2013 Fusion, using T harness, Evo all in one, red and blue do their blinking thing then stay steady. put key 1 in and turn red flashes wait 3-6 seconds then remove key, red stays on. Put key 2 in and yellow flashes, wait 3-6 seconds, remove key, yellow stays on. Car turns on like its in run position then says no keys found. Blue light never comes on.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer