Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Wire diagrams for 1996 honda acty jdm or equivalent?

I have a jdm honda acty I drive it everyday now that is cold out I would like to install a starter. The car is carbonated so it take a min to warm up is there a different American car wire diagrams I could follow to install my own remote start.

0

2000 Honda CRV 7 pin not find

I can't find the 7 pin connector

0

How to Wire Clutch Pedal Stroke Sensor for 2020 Honda Civic Type R

Hello I have the Evo-One and Fortin THARONE-HON7 T-Harness. Everything is wired up but I'm not sure how to create a relay to connect to the clutch pedal stroke sensor.

0

Fortin Evo One + Honda 7 harness for 2020 Civic Type R

Hello, I'm currently having issues starting the car up currently. I have tried to reseat all the connections and double checking but after following the directions and updating my Evo One unit, my car will not detect my key fob at all. So I cannot start my car at all even with the key fob right next to the ignition start button. I can't remote start the car either, the key fob buttons do work though. Any help or suggestions would be very much appreciated, thank you! 2020 Honda Civic Type R (Manual transmission) Evo one + Hon7

0

Clutch Bypass 2018 Civic Type R

Hello, I am using an EVO ONE with the HON 7 T-Harness. I have wired everything and cannot seem to get the vehicle to remote start. I read that the clutch pedal stroke sensor needs to be open, by open does that mean I need to simply cut the red wire and leave it loose? Should it be connected to something else? Thank you for your time.

0

2019 Civic PTS Security Bypass Not Working and Incorrect clutch bypass

Issue 1: The remote starting fails to successfully start the vehicle. 

During cranking the dash security indicator continously flashes, this indicator is normally only flashing when the vehicle has been locked.  The dash security indicator begins to flash after the vehicle is shut down by the remote starter (from Ready Mode) and continues to flash until the vehicle is unlocked with the remote.

Parking light flashes four times after each failed cranking attempt.

Ready mode is operating as indicated, pressing brake while engaging the parking brake, then lifting off.  One parking light flash is indicated, the Red and Ylw leds on the EVO are on, and the motor continues to run until the driver door is open then closed.  Once the vehicle is shut down the dash security indicator begins flashing.

Blue Led flashes with each Lock Key signal from the OEM fob.  After three lock signals the Red and Ylw LEDs on the evo turn on and the start sequence begins.  The dash indicators come on and the dash security indicator led remains flashing. The starter is being actuated and the engine is cranking but the car does not successfully start.

Issue 2: Opening Red Wire on 4P clutch conenctor causing VSA and parking brake errors

In addition to the HON7 t-harness, Cut3, tap on Ylw line of Clutch Position sensor, and open of Red line on Clutch Stroke sensor (type R only) has been performed.

Without the opening of the Red line on the Clutch Stroke sensor the car will not activate the starter motor during remote starting unless I manually press the clutch pedal.  Once the Red line is opened as instructed, the remote start does actuate the starter motor, but now during normal operation there are now CONSTANT VSA and PARKING BRAKE ERRORS indicators on the dash. The vehicle does run and drive but with errors.

I posted this link in my earlier question, but it appears that opening the Red line causes the VSA system to malfunction and putting a relay on the Ylw line of the Clutch Stroke sensor maybe an alternate method? I am not sure how to do this with the EVO configuration.

https://github.com/JW0914/Wikis/blob/master/Automotive/FK8%20CTR/Compustar/Alarm%20%26%20Remote%20Start%20Install.pdf

Please advise on updates or alternate configuration. My setup specifics are listed below:

Vehicle: 2019 Civic Type R PTS Manual

Bypass HW: 4 FW :3.32

Remote Starter HW:7 FW 1.24

T-harness: HON7

All reccomended options were loaded for both Bypass and Remote Start, only the Ready Mode Option was modified from 33.1 to 33.2.

The decryptor programming was performed twice with nominal LED and Flah Link Updater feedback

0

2019 Civic Type R Red Wire Clutch Switch Location

The EVO wiring instructions specify that the 2019 Civic Type R (Push-to start) has an addtional red wire on a four pin Clutch Switch; this wire need to be cut. I could not locate this Clutch Switch connector with a red wire in a 2019 Civic Type R (USDM) and could not find any pictures or other references to this connector location in the instructions. The only connector near the clutch assembly is the a four postion 2 wire connector that matches the docutmentation, this connector has only the yellow and black lines. Where can I find this additional red clutch wire? Thanks, Bryan

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue