Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

2015 Tundra cannot get the FX44 keyfobs to work

OEM keyfob remote start works but cannot get the FX44 keyfobs to work. actually cannot even get the LED on the antenna to come on.

0

Can't get remote start to work on tundra with Evo-one

Fortin Evo-one help


So I installed the Fortin Evo-one today and I can't get it to do anything. I have checked my wiring 3 times to ensure I have it correct and it looks good. I get through the bypass programming procedure successfully but it won't do anything. I see the blue light on the unit flash when I hit the lock/unlock button. When I press my oem remote lock 3 times it just does what it did before I had the evo installed (beep and parking lights with each press).

I think I have it programmed correctly but could use some help. Could it be that I have the OEM alarm with shock sensor installed? Is there a setting I need to change for that?

Here is what I have set:
Bypass firmware 79.31- below are things that are on
A3- Key Bypass
A5- Aux 1 can't turn this off I get an error that the unit doesn't support this
A6- Aux 2 can't turn this off I get an error that the unit doesn't support this
A8- Hand-Brake (output status) can't turn this off I get an error that the unit doesn't support this
C1- OEM Remote Monitoring

Remote-starter firmware 1.16
2.4
3 tachless sensitivity: 1
4.1 (runtime)
6.2 unlock before remote start and lock after remote start
7.1 Safety locks: none
8.2 Unlock pulse time: double 0.25 sec pulse
9.1 Active or passive starter kill: Active starter kill. press lock to activate the alarm and starter kill
11.2 Confirmation: lock/unlock sound always
12.1 Sound confirmation: horn only. output programmed to be used for vehicle horn
13.2 Pulse confirmation: short
14.2 Alarm and Starter options: Alarm enabled, remote starter enabled.
15.1 Smart door lock: disabled
16.5 Cold start timer: off
18.1 disable disel mode
19.1 disable turbo mode
20.6 Tach data-link only
21.1 start attempts 2 times
24.1 Special applications disable
25 Off
26.1 gas/diesel vehicle
29.1 Alarm duration 30 sec
30.1 Valet Code: Ignition ON + 3x valt button 
31.1 Special application programmable output: Disable
32.1 Ground out: Shut down 1s after remote start run time. Dark Blue wire (ground out)
33.1 Manual transmission ready mode activation: Activated by remote starter remote. Ready mode activated with the starters remote
34.1 Trunk output: Pulse 0.5 seconds
35.1 Door lock special application: Disable
36.3 Activation/Deactivation remote Valet mode: By valet button only
37.1 Security remote car starter special application: Disable
38.2 System control by OEM remote: Enable (press 3x lock to remote start (bypass module required)
39.1 Temperature control: Disable

I also noticed I can't get programming to work with the valet button.  It won't do anything. 

I have a 2016 Toyota Tundra TRD Pro and I used the evo-one with Ttoy2 harness. Truck has the OEM remote with shock sensor. 

-Ruben


 


 

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue