Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Subscription didnt activated

Can you please add my token i already paid for it . I have to work on the car thank you

0

Subscription didnt activated

Can you please add my token i already paid for it . I have to work on the car thank you

0

How to hook up power windows as aux with Evo One on 2017 Tundra?

Hello, how would I go about hooking up my power windows to roll up and down on 2017 Tundra equiped with Evo One?

0

Rear Defroster

Hi I have an 2009 Toyota Corolla S My question is I want the rear defroster to turn on when I remote auto start the car . Can I wire it to an aux and if yes where should I connect and which one I should use. or can i just use Evo FlashLink to setup it . Thank You

0

Where to connect the Yellow wire on the Evo start 2. Using EVO one and THAR TOY 8

Using the THAR TOY 8 and EVO ONE, wanted some clarification on where to connect the yellow wire from the EVO Start 2.

0

Harness for OBD2 connector? (re: +12V/GND) ...and do I need IDLE MODE wire?

I'm installing an EVO-ONE with T-harness into my 2018 Toyota RAV4 Hybrid. However, the installation manual (https://cdn02.fortin.ca/download/71281/evo-one_ig_thr_bi_toy6-rav4-hyb_2017_pts_a_71281.pdf) shows an optional wire for "IDLE MODE" that connectrs to the wiring behind the PTS button? It says optional but what am I missing if I don't connect it? Is it worth connecting? Also, even though I've purchased the T-harness, the instructions show that I need to connect to the OBD2 wires for +12V and GND. Do I need to cut these wires behind the OBD2 connector or is there an easier or other recommended place to connect the wires?

0

19' Camry Std Key which wiring guide to follow for RM411 RF kit?

2019 Toyota Camry with Std Key. EVO-One with Fortin RM411. The wiring guides for both do not match. Which one do I follow?

0

dashed wires in pdf diagram should be connected or not?

hello i am installing evo all to my rav4 2018 pts non hybrid .. i see (-)START/STOP in dashed lines vs other solid lines? .. what does dashed line mean? connected or not? like also thw two : (-)AUTOLIGHTS OFF

0

cutting the right wires

Using the evo-ride bypass for my 2004 Toyota Camry and just want to make sure I read the diagram right. I am supposed to cut the IMI cable(yellow) into two and splice the white/red from the 3 pin conn. to the connector side of the IMI wire. While the yellow/black from the 6 pin conn. and the white/green from the 3 pin connector gets spliced into the car side of the IMI wire. Correct me if I'm wrong. Thanks.

0

2014 toyota tundra evo all in one with t harness

do i have to splice into the t-harness with the pink ignition wire going to the yellow A1 ??????????

0

EVO-All Installation to Toyota Tundra 2014- 1794 edition

Dear Sirs, I have Toyota Tundra 2014- 1794 Edition and I wish to instal Evo-All for remote start. Please provide wiring instructions for my model. BR.

0

EVO-All Installation to Toyota Tundra 2014- 1794 edition

Dear Sirs, I have Toyota Tundra 2014- 1794 Edition and I wish to instal Evo-All for remote start. Please provide wiring instructions for my model. BR.

0

Colors and numbers of wires in 30-pin connector in vehicle do not match with details in EVO-ALL installation guide!

Hi

 

I am attempting to install an EVO-ALL stand alone remote starter on a Toyota RAV4 Hybrid (2016, push-to-start). Until I got to the 30-pin connector the installation proceeded smoothly as described in this guide: http://fortin.ca/en/download/58691/58691.pdf

 

As you can see from my attached photos the wires on the 30-pin connector in question look different than the one pictured in the guide downloaded from fortin.ca ('58691.pdf'). A couple of wires do not exist in my vehicle (among others: blue and red wires for tapping into RX and TX respectively).

 

Do you have any recommendations on how I can continue and complete the installation?

 

Thanks.

 

Link to previously attached photos: https://jimlarsen.ocloud.de/index.php/s/HrIMS9quD2v6ewg

01/09/2016