Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Honda SL3 blue wire required?

I'm installing the Honda SL3 on a 99 Accord for immobilier bypass only (no remote start) on a replacement ECU. Based on the instructions... https://cdn02.fortin.ca/download/27521/honda-sl3.revzc.pdf I'm not clear on the blue wire. If I am not using a remote starter do I just ignore that wire? If not, what exactly is it wired to?

0

Alarm start sound when the car start with the remote starter.

I installed a remote starter crimestopper Rs1-g5 with a bypass crimestopper Honda-sl3 in a Honda Civic 2006 standard key, automatic transmission. The problem is, when I start the car with de remote starter, the car start, but the factory alarm start sounding and the flashing lights too.

0

Honda-SL3 compatible with Viper 5706 via D2D

I am wondering if the Honda-SL3 bypass module can be connected directly to the D2D port on the Viper 5706 alarm?

0

Honda-SL3 & Compustar CS800s connection

I'm hooking up a CS800s in a 2007 Honda Pilot. I will be using a Honda-SL3. There is a wire that I'm supposed to connect to the remote start unit, but I cannot figure out where to connect it.

-1

I purchase and started installing a Honda SL3 Bypass module on my 2013 Honda civic. Can that module work??

The alarm used was Autopage RS730. We connected the alarm, found the starter wire and connected to output. Whenever key is press 2 times, the ignition comes on, the car engine turns over but wont start. The key light blinks 4 times. The module was not programmed as yet thou. There are 4 connection that ought to be connected from the bypass module to the Key immobilser section. Data, Lamp in, Lamp out and Synro I would like a diagram displaying where these connections must go to or a diagram displaying where the data, lamp in and out wires are on the car Key Immobilser harness

-1

I purchase and started installing a Honda SL3 Bypass module on my 2013 Honda civic. Can that module work??

The alarm used was Autopage RS730. We connected the alarm, found the starter wire and connected to output. Whenever key is press 2 times, the ignition comes on, the car engine turns over but wont start. The key light blinks 4 times. The module was not programmed as yet thou. There are 4 connection that ought to be connected from the bypass module to the Key immobilser section. Data, Lamp in, Lamp out and Synro I would like a diagram displaying where these connections must go to or a diagram displaying where the data, lamp in and out wires are on the car Key Immobilser harness

0

Honda SL3 loss program 3X in 2 months

I installed Compustart CS800S and Honda SL3 onto my 2005 CRV about two months ago, during two months, I had to re-program SL3 three times. 1st time it happens when I was inside the car testing the remote start, when the car starts cranking (but did not run as of yet), I insert the key into ignition and after that, it stopped working (it will crank but won't start and key symbol flashes on dash), I figure I put the key in during cranking caused the module to loose the program so I reporgram and all was ok. few weeks later, It happens again but I did not do anyting this time, so, I find it to be odd but again, I reprogrammed it and was ok. It happend again two weeks after, I am thinking the module is faulty, I see no reason why I had to do this over and over again, all wiring were soldered and I checked it again today. Any input?? Thanks in advance.

0

I'm having identical problems with HondaSL3 on two different vehicles

I'm working with a 2003 Pilot and a 2013 CRV. In both vehicles the programming seems to complete normally, but the remote starts behave as if the bypass was not working. We checked all wiring - everything is correct (we do 100's of SL3's) no t-taps. Both vehicles crank, run for a second, then shut down. On the Pilot, the security light comes on after the failed start attempts. Any suggestions?

0

Honda Stream RSZ 2010 (Japan) Honda-SL3

I need to connect Honda-SL3 to the Honda Stream 2010 with the ignition key. Please send me the wiring diagram.

0

No white wire Element 04

When asked to cut the blue and white wire ,no white wire in the data link

04/05/2014

Honda (Pts.)

0

will a Fortin Honda-SL3 work on 2008-2009 honda accord Ex-l

will a Fortin Honda-SL3 work on 2008-2009 honda accord Ex-l. im asking because ive bought the sl-3 couple years back for my 98 accord

18/02/2014

Honda (Pts.)

1

14 CRV WITH SL3 , STARTS ONCE THEN WON'T START AGAIN.

HI, GREG AT HONDA DEALER....WHEN USING SL3 IN 14 CRV AND 14 CRV UPDATE, WE HAVE HAD A NUMBER OF VEHICLES WITH A CONDITION WHERE THEY WOULD START ONCE ,THEN WHEN TRYING TO START AGAIN THE KEY LIGHT WOULD FLASH AND VEHICLE WOULD NOT START UNTIL STARTED WITH KEY FIRST....SOFTWARE GLITCH? OR NOVICE INSTALLERS?

0

Instructions of SL3 in 2012 CRV conflicts with wire color, pin# and diagram?

Instructions of SL3 in 2012 CRV conflicts with wire color, pin# and diagram. The chart says data is yellow in pin #2, the diagram 4 says data is pin #6. Which is what for the data and ignition wires ???

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer